Installation and commissioning of Fleck 5600 water softener-Yuanlai Water Treatment

font: Big Middle Small

Installation and commissioning of Fleck 5600 water softener

Released Date: Dec 21,2015 Article Source: Yuanlai Water Treatment

The installation of the water softener should be carried out by connecting the inlet, outlet and sewage outlet pipes as recommended by the manufacturer, and should comply with relevant pipeline specifications. Manually turn the control valve of the water softener to the working position to allow water to flow into the resin tank. When the water flow stops, open the inlet and outlet until all the air in the pipeline is discharged, and then close the inlet and outlet. Note: You can manually rotate the knob at the front of the control valve to set it to different regeneration positions until the water softener is displayed at the desired position. 2. Manually turn the control valve to the backwash position to allow water to flow out of the drain for 3 or 4 minutes. Example figure: 3. Remove the rear cover plate of the control valve. Example Figure: 4. Ensure that the amount of salt used is set as recommended by the manufacturer. If necessary, set the amount of salt according to the setting manual. Manually turn the control valve to the brine refilling position to fill the void with water

　　1.Manually turn the control valve of the water softener to the working position to allow water to flow into the resin tank. When the water flow stops, open the inlet and outlet until all the air in the pipeline is discharged, and then close the inlet and outlet.

　　Note: You can manually rotate the knob at the front of the control valve to set it to different regeneration positions until the water softener is displayed at the desired position.

　　2.Manually turn the control valve to the backwash position to allow water to flow out through the drain outlet3or4Minutes.

　　Example diagram

5600Control valve

　　3.Remove the rear cover plate of the control valve.

　　Example diagram

5600Rear end of the control valve

　　4.Make sure the amount of salt used is set as recommended by the manufacturer. If necessary, set the amount of salt according to the setting manual. Manually turn the control valve to the brine refilling position to fill the top of the air check valve with water.

　　Example diagram

5600Control valve

　　5.Manually turn the control valve to the brine suction position to draw water from the brine tank until it stops.

　 Flow type

　 6.Connect the power supply and observe the sight hole on the back of the motor to see if it is running. Regeneration can be set through the flow disk.

　　Example diagram

5600Control valve

Time type

　　Each thin slice represents a day. The thin sheet at the red pointer represents the day. When the red pointer is turned clockwise, the thin sheet can be pulled out or pulled back to obtain the required regeneration time arrangement.

　　7.Manually push the beginning of the salt water refilling position of the control valve forward to allow the control valve to automatically return to the working position.

　　8.Add salt to the brine tank.

　　9.Install the control valve rear cover.

　　10.Make sure the bypass valve is in the normal working position.

　　The above is provided by Beijing Yuanlai Water Treatment. If you encounter any problems during the selection and use process, please consult Beijing Yuanlai Water Treatment Equipment Co., LTD.15With years of focus on the water treatment industry, you can trust us!

Keywords: Water Softening Equipment Automatic Water Softener Reverse Osmosis Equipment Manufacturer of Water Treatment Equipment

Prev : RO reverse osmosis equipment, reverse osmosis, pure water equipment

Next : Water quality standards for softened water equipment

Recommend products

: EDI ultra-pure water system

Yuan LaiEDIThe ultra-pure water equipment uses electro-deionization technology.EDIElectrodeionization is a water purification method that combines the dual advantages of electrodialysis and ion exchange. It does not require acid-base chemical regeneration and can continuously and stably prepare high-purity ultrapure water. Under the action of a direct current electric field, ion separation in water is completed. At the same time, water is electrolyzed to generate hydrogen ions and hydroxide ions, achieving automatic regeneration of the resin without the need to stop the machine for manual regeneration. The pre-treatment combined with reverse osmosis can prevent oxidized substances from damaging the resin, ensuring stable effluent quality and widely meeting the high-standard water usage requirements of various industries.

: Non-negative pressure water supply equipment

The non-negative pressure water supply equipment can be directly connected to the municipal water supply network, making full use of the residual pressure of the original network for superimposed water supply. Fully enclosed operation does not require the construction of a domestic water tank, eliminating secondary pollution. Intelligent variable frequency voltage stabilization, energy-saving, quiet and easy installation, it is the preferred equipment for secondary water supply in high-rise residential buildings and commercial buildings.

: Constant pressure water supply equipment

Constant pressure water supply equipment is widely used in central air conditioning, floor heating, industrial closed-loop water circulation, and boiler systems. It integrates automatic pressure stabilization, automatic water replenishment, automatic exhaust, pressure relief and buffering functions. It stabilizes the pressure in the pipeline network, eliminates abnormal sounds caused by air blockage, and prevents damage from negative pressure and water shortage in the pipeline. It is an essential supporting equipment for HVAC and circulating water systems.