Time type Flow-type fully automatic water softening equipment

　　Our company adopts multi-way valve control systems from American companies such as Artuzu and Fulaike, and designs and produces fully automatic softening equipment in combination with national conditions. It is widely used in the preparation of industrial and civil softened water, such as boiler water supply, heating, supplementary water for air conditioning systems, and good domestic water supply, etc.

　　The fully automatic softening system mainly consists of multi-way valves, controllers, resin tanks and salt tanks. The multi-way valve is designed with multiple channels in the same valve body.

　　Technical parameters of the softener

　　1Raw water hardness≤6[H+]mmol/L

　　2That is300 mg/L("CaCO3meter)When the hardness of the raw water is6--12[H+]mmol/Lwhen

　　3It is recommended to adopt two-stage softening or appropriately reduce the output of the effluent

　　4When the hardness of the raw water≥12[H+]mmol/LIt is recommended to adopt multi-stage softening or contact our company's engineering and technology department for targeted design.

　　5Effluent hardness≤0.03[H+]mmol/L("CaCO3"Calculate

　　6Work pressure:0.20--0.50Mpa

　　7Working temperature:2--49℃

　　8Raw water turbidity:<5NTU

　　9System water consumption:<2%

　　10Regeneration salt consumption:120-180g/lResin (generally acceptable.160g/l"Resin

　　11Working power supply:AC220V,50HzSingle-phase three-wire system

　　12Working power consumption:<10W

　　13Periodic water production capacity:Q=V×E/(IRaw water－I"Effluent

　　QPeriodic water production capacitym3ort

　　VResin volume usagem3

　　IRaw water: Raw water hardness[H+]mmol/L

　　IEffluent: The hardness of the effluent is required[H+]mmol/L

　　EThe working exchange capacity of the resinmmol/L,Generally, it is based on the full exchange capacity of the resin60%--70%Calculation.

　　As long as you understand and provide the following parameters to our technical department, you can accurately select the softener that meets the requirements of your organization's system equipment.

　　◇ 1. First, you need to provide the system that requires softened water: process water? Heating? Cooling water replenishment? Steam boiler? The steel smelting industry? Chemical and pharmaceutical industry?

　　◇ 2. System water usage time: Clearly define the operating time/Hourly water consumption/Average value/Peak flow

　　Does the user need continuous water supply? If necessary, choose the single-valve dual-tank or dual-control dual-bed series; otherwise, the single-valve single-tank system can be selected.

　　◇ 3. Total hardness of source water? Is the water source municipal tap water? Groundwater? Surface water source (river,The river,For lake water, you need to provide the hardness of the raw water in the area where it will be used. For a certain model of water softener, if the water hardness is high, the periodic water production volume must be less, which in turn leads to frequent regeneration. It is detrimental to the service life of the resin. To avoid this situation, the volume of the resin should be increased, which means choosing a larger model of water softener.

　　If you are not familiar with the water quality of the water source you are using, you can entrust it to our company's analysis laboratory. We offer free routine water quality analysis.

　　◇ 4, The required unit flow rate of soft water (tons)/(hours). This is determined by the nature and requirements of the user's equipment, based on which the standard model of the water softener is selected.

　　◇ 5The setting of the periodic water production capacity

　　After the model of the water softener is set, the theoretical cycle water production (in tons) can be determined based on the hardness of the raw water and the exchange working capacity of the resin used.

　　Selection Guidelines for Softening Equipment

　　◇ 1Controller: From the United StatesFLECKFleckAUTOTROLArtuzu automatic control valveAQUAMATICYAKE Ike

　　◇ 2Resin tank: Available for selection: DomesticRFPCans, metal-lined plastic cansPE"Inner lining

　　Import (StelloRFPtank

　　◇ 3Equipment operation control form:

　　L- Flow type: Automatically restores when the prepared water volume reaches the set value, which is suitable

　　Used for the preparation of soft water in all water supply systems.

　　S- Time-type: It is a regeneration metering method controlled by time, suitable for water supply in systems with stable water consumption, and has a short restoration and regeneration cycle24Hours.