Fully automaticWater softenerIt is to assemble the traditional communication system and recovery system into a whole, and automatically end the entire process of softening and regeneration through the pre-set program of the controller. We call this equipment a fully automatic water softener, also known as an automatic water softening device. The fully automatic water softener mainly consists of a communication tank, a salt supply tank, a controller (except for the inlet and outlet water ports, all other working pipe interfaces are integrated inside it), etc.

　　In life, water softening equipment has brought me a lot of convenience. Removing hard water has more benefits. It can prevent scaling and pipe blockage that occur during long-term use, reducing economic losses. In addition, he also needs long-term maintenance to extend the service life of the equipment. Now, let's have the editor share with us the maintenance methods during the operation of water softening equipment.

　　1Ensure the stability of voltage and current to prevent equipment from being burned out. Electrical control equipment should be well sealed to avoid water immersion and moisture.

　　2Add solid salt to the salt tank on time. Do not add iodine-rich salt. Be careful not to spill it into the salt well to avoid clogging the salt suction pipe. Regularly deal with the impurities at the bottom of the salt tank. Just rinse it with clean water until there are no impurities!

　　3The water softener should be disassembled and cleaned once a year. Remove impurities from the water distributor and the quartz sand pad layer, and check the consumption and communication of the resin. If there is severe aging, it should be replaced in time. For resin poisoned by iron, it can be revived with hydrochloric acid solution.

　　The boiler water softening equipment produced by Beijing Yuanlai Water Treatment Company can work stably for a long time, and the water quality meets the needs of users. We will continue to do our best to provide users with more satisfactory efficiency and equipment. Customer satisfaction is our top priority.

　　The fully automatic water softening equipment is an indispensable water treatment device in the north. Every winter, after the heating season ends, the fully automatic water softener stops providing heating. At this point, problems will arise with the fully automatic water softening equipment. If softened water is not used for a long time, it will grow. Microorganisms will affect the communication ability of the resin. If backwashing needs to be arranged at a certain time as required, it will consume a lot of water. At this point, we put forward the following suggestions to maintain the function of the fully automatic water softening equipment.

　　1.Adhere to the regular cleaning of the fully automatic water softening equipment, ensure a satisfactory supply of oil when adding it, and be careful not to touch the pulley during operation. This can prevent accidents from happening.

　　2.Suppose the fully automatic water softening equipment is out of use for half a month, and the nylon pipe for discharging wastewater is raised on the communication column to ensure continuous drainage. When it is not used for a long time, the salt tank and resin should be cleaned, and rust on all parts of the equipment should be avoided. The water softener that is about to be shut down can be regenerated. When the brine is completely absorbed, the regeneration process can be interrupted and the water softener sealed. Soaking this resin in the regenerated brine in this way will not cause bacteria to grow even when the equipment is reused, and the resin will not be affected. However, the brine should not be soaked for a long time either. Because organic matter was brought into the salt water,After long-term soaking,The water will smell much worse than ordinary tap water.If soaked in salt water,Generally, do not overstep it.2One month.It is recommended to maintain it with clean water after regeneration.It might be better to assume that an appropriate amount of agents can be added.However, it will have a direct impact on the lifespan of the resin; When not in use for a long time, the remaining salt solution in the salt tank and the valve body should be cleaned. Lubricating oil should be added to the rotary valve and all transmission parts to prevent equipment from being induced. If the machine is shut down for more than half a month in summer and during the moldy season, it should be started60120Take minutes to prevent the microorganisms in the resin tank from getting moldy. When starting from the beginning, first manually rotate the manual regeneration wheel clockwise. The water softener then initiates the regeneration program and will complete one regeneration cycle according to the set working process, returning to the working condition (producing soft water).

　　3.Some local areas should also take the environment into consideration. For instance, in Beijing, some pump rooms are located in basements, and it doesn't matter much whether they are backwashed or not in summer. However, some are on the ground, where even sunlight can directly reach them, and the ambient temperature is extremely high! Then you need to be punctual and recharge. In addition, after the equipment is shut down in summer, the stagnant water in the incoming water pipeline also poses a significant threat to the resin. It is recommended to drain it before flushing! Especially after the pipes were vented and repaired, I have seen users' tanks piled up50The yellow soil dominated by centimeters, after the lower water pressure was folded, it was discovered that it was due to the construction of the external pipeline network renovation.

　　4When the fully automatic water softening equipment is in operation, do not adjust the time of the relay. Only after the power supply is cut off can the equipment be repaired and cleaned. This is to fundamentally prevent defects such as water ingress in the motor, distribution board, and limit switch. When operating, supply water and power simultaneously. When shutting down, shut off all water and power sources. Each time a user stops the machine, it should not be done within a short period of time. Instead, both the machine and water supply should be cut off simultaneously.