Fulake Water Softening Treatment Equipment6Tons of/Xiaoshifuleike water softener

BeijingFleck softenerYuan LaiAtu group multi-way valveBeijing YuanlaiFully automaticSoftened water treatment equipmentYuanlai Environmental ProtectionBrand water treatment softener.

Product Introduction

Category: Fleck Water Softening Equipment

Brand: Fleck, USA

Application: Water softening treatment equipment

Modelonelynn-6

Product Description: This equipment is imported from the United StatesFLECK

The company's control device is a fully automatic ion exchange that is domestically assembled and formedSoftened water equipmentThe manufacturing processes and technologies both at home and abroad are adopted. The resin tank is made of high-quality anti-corrosion materials such as fiberglass reinforced plastic, stainless steel and carbon steel lined with plastic. The equipment is of excellent quality, stable and reliable performance, and has achieved fully automatic operation of the water softening equipment without the need for dedicated management. The performance-to-price ratio is higher than that of similar domestic products. It is widely applied in boilers, air conditioners, refrigeration and other systems of industrial or civil sectors such as petrochemicals, light industry and textiles, health care, hotels and restaurants.

I. Design Selection Guide

1Equipment selection

Softened water equipmentThe main basis for selection is the water demand, the hardness of the raw water and the applicable occasion

2,There are various models of equipment with the same water output, and they can be selected according to the actual water usage.

3,Water usage scenarios: If a hot water boiler or other similar equipment is used, the selection can be made based on the high-water production capacity of the equipment. If water is supplied to a steam boiler, it is generally based on the boiler's evaporation capacity

4,It should be matched with the water production capacity of the equipment.

Ii. Key Points for Design and Installation

The equipment itself has a simple structure and occupies a small area, so there are no special requirements in terms of design and installation. When designing and installing, only

The following points should be noted:

1,The equipment requires a simple horizontal foundation. About from the wall250~450mmIt can be arranged at the corners according to the actual situation.

2,Since the equipment itself is relatively light, generally only the weight of the resin and water it contains needs to be considered.

3,The inlet and outlet water pipes are standard flange or threaded connections and need to be fixed and supported well. They should not rely on the valve body for support to prevent stress.

4,A water pressure gauge should be installed on the water inlet pipe. When the equipment is in operation and flushing water is discharged, a floor drain or drainage ditch should be set up nearby

5,Salt water pipe: The salt water tank should be as close as possible to the softening tank, and the shorter the salt water pipe, the better.

6,The sewage pipe should not be longer than6Do not install a stop valve. The outlet should not be higher than the valve body. The terminal should be open to avoid siphoning. The fewer elbows, the better.

7,Power distribution sockets should be installed on the wall near the equipment and be equipped with fuses(Generally, do not install switches)Good grounding is required.

Iii. Scope of Supply and On-site Installation Requirements

1Scope of supply

Provided by our companyFully automatic water softening equipmentThe supply scope includes multi-way valve bodies, controllers, solenoid valves, resin tanks, salt tanks, salt Wells, salt valves and main pipe fittings(Some models do not include an outlet solenoid valve). The standard equipment does not contain resin. Refer to the installation diagram in the manual. Components other than the water inlet and outlet shall be prepared by the user. For specific details, please consult the seller.

2On-site installation requirements

Fully automaticFulake water softening equipmentThe system structure is simple and the requirements for the installation site are relatively low. However, some tasks require the user's cooperation. The main tasks include: ensuring the normal operation of the system with sufficient water pressure and installing a pressure gauge for the water inlet. Ensure that the suspended solids content in the water source is lower than the requirements of the water softener. If the suspended solids content in the incoming water is relatively high, a filter should be installed. Provide the power supply required by the system; Provide a horizontal foundation for the equipment.